Help, I have no hot water

It can be frustrating to suddenly discover you have no hot water for a bath or shower. This guide will help you to identify the cause and find a solution.


Air source heat pump

Air source heat pump systems require a hot water cylinder for storing the home’s hot water.

  • The hot water may be scheduled off: please check settings on the control panel and alter if necessary. Ensure Direct Hot Water mode is operating and wait for the hot water cylinder to re-heat.
Air source heat pump
  • If there is a fault displayed on the control panel, refer to the manufacturers operating manual to find out what the problem is.
  • If your home is still under warranty, please get in touch with your local Customer Care team.

Combi system

Your hot water should be provided 'on demand'.

 

  • Make sure your boiler is switched on and the display does not indicate a fault.
  • If there is a fault displayed, use the manual that came with your boiler to find out what the problem is. 

  • If the boiler is on and there are no faults showing, try running the hot tap nearest to the boiler, most likely the one over the kitchen sink. Watch the boiler display as you do this, noting any faults that are displayed.
  • If your home is still under warranty, please get in touch using the Contact Support box on this page.
    Your hot water should be provided 'on demand'.

Conventional system

With this type of system you’ll have an airing cupboard containing a hot water cylinder.

  • If you’ve simply run out of hot water, you can use your immersion heater boost programmer. Remember, immersion heaters use a lot of energy and can be more expensive to run. The switch will probably be in the cupboard with your boiler.

Conventional boiler

  • Check your boost programmer is set for long enough to provide a sufficient amount of hot water.
  • Check the front panel of your boiler to ensure that it is running correctly and displaying no faults. If all seems well, you may want to adjust your hot water settings to better suit the needs of your family.
  • If there is a fault displayed, use the manual that came with your boiler to identify the problem. If your home is still under warranty, please get in touch using the contact box on this page.

Shower only is affected

If it’s one shower that’s affected, it’s likely to be one of three reasons:

  • Electric showers are unaffected by a general loss of hot water, since they heat water direct from the mains. So if your electric shower isn’t working it may not be getting power, or could be suffering from an internal fault. Read our showers guide to find out how to identify your electric shower and make sure it is switched on at the mains.
 
Electric shower
  • If there’s no water at all, it’s likely this particular tap has been disconnected from the hot water supply, possibly during plumbing work or maintenance.
  • If you’ve just moved in and this outlet has never delivered any water, please get in touch using the contact box on this page.

Bath or sink only is affected

If you’re having problems with just one bath or sink, there are a number of possible causes:

  • If you can’t get your bath water hot enough, it could be linked to the temperature restrictor, fitted as standard. Find out more in our guide to baths, sinks and taps.
  • If your bath or sink is running only cold water, try running the tap for longer to see if it heats up. Check other taps to see if they eventually run hot.
 
Sink

  • If there’s no water at all, it’s likely this particular tap has been disconnected from the hot water supply, possibly during plumbing work or maintenance.
  • If you’ve just moved in and this outlet has never delivered any water, please get in touch using the contact box on this page.

All your outlets are affected

If the problem is not isolated to just one outlet (sink/bath/shower) and you’re only getting cold water from your taps, it could be you’ve run out of hot water, or your boiler or cylinder isn’t working properly.

To work out which, you first need to know what type of heating system you have. If you aren’t sure, please use our guide: What kind of heating and hot water system do I have?

A common problem with all types of boilers and cylinders is a lack of pressure. Read our guide to setting up your heating and hot water to find out more.

District heating

If you have district heating and are experiencing issues with your hot water, first check whether your neighbours are affected.

If so, it’s likely to be a problem with your local energy provider, and you should contact them in the first instance.

Other reasons you might have not hot water

If you’ve checked all the above and your taps or showers are still not delivering hot water, it’s possible the hot water to or from your boiler has been switched off or disconnected.

This could be the result of recent plumbing work or servicing. In which case, please contact the tradesperson responsible.

If you haven’t had any such work, and your home is under warranty, please get in touch using the contact box on this page and we will do our best to help you.

Emergency

Our teams are on hand when you need us, especially in the event of an emergency.

Get in touch

The New Home Customer Care Team is available via phone and email.